How to Replace a Kia Sportage Replacement Key
The key of many Kia models comes with an entry system that is keyless in. This key is similar to remote controls and is exchangeable by a Kia dealer.
Key fobs might stop working for a variety of reasons, such as an empty coin battery worn buttons signals, water damage, signal interference and a damaged receiver module. Here are some tips on how you can get your Kia Sportage replacement key to work again.
How to replace the remote key or smart key
The battery inside your Kia's smart key will eventually require to be replaced, whether it is a remote key or a push-to-start one, or a regular metal key that is not equipped with an electronic transponder. This is particularly relevant if your vehicle displays a message indicating that the remote or smart keys have low battery power.
Luckily, it's a relatively simple process. In order to replace the battery of the key fob remove the mechanical key from the slit in the back of the key fob. You then need to pry open the cover. Inside the key fob there will be tiny screws that hold the battery in place. By using a small screwdriver remove the screw and pull out the battery that was in place. Insert the new battery and close the opening on the key fob.
Test the key fob by pressing the lock/unlock buttons. You're good to go when the doors lock or unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to complete errands in Brandon.
Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key has to be programmed again, you will need to be aware of the key code that is stamped on the tag that identifies the key and record it in a secure location.
How do you replace a dead battery?
If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly could cause other issues like the check engine light flashing on or a delay in cranking the engine. It is easy to replace key fob batteries by using only the use of a few tools.
Be sure to turn off your vehicle and close the doors before you begin. Find the small metal or plastic piece on the bottom of the key fob. Press it until the key pops out. The key can be placed inside the driver door handle to unlock your car.
To replace the battery on the key fob, remove the cover at the rear. Use a pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then place the new battery so that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the contacts on the metal.
Once the new battery has been installed and the key fob is turned on, turn it off and back on in the ignition repeatedly until the door locks. You can then test the Kia's Key fob again to confirm that it is working correctly.
How to replace kia rio car key cover
Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference between them is that the smart key is equipped with an incredibly small key blade that is hidden inside, while the standard fob isn't equipped with. Both key fobs are equipped with batteries that will eventually need to be changed. It's quite simple and will take about two minutes.
Make sure you turn off your Kia, and be on a level or well-lit surface prior to when you begin. Remember that the fob contains tiny parts that could be thrown off when you're not careful.
The first step is to locate the small release button on the back of the lower part of the fob. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.
Once the key fob is open, remove the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. After installation it should be possible to lock, unlock and start your vehicle with your key fob even if your engine isn't running!
How do you replace a broken mechanical key
The Kia key fob is an amazing feature that lets us lock and unlock our car with the touch of the button. However, like all devices, it can have problems occasionally. There are solutions to fix these problems and keep your key fobs running for an extended period of time.
A dead or drained battery is one of the most frequent problems. This can cause your fob to stop working or operate intermittently. If this is what you are experiencing then replace the battery with an entirely new battery.
If this isn't enough to resolve the issue Try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a new one.
Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the key fob and check that it's functioning correctly. If the device not working, contact a dealer or locksmith to resolve the problem. To avoid lockouts in the future, ensure you have an emergency key that can work in all of the door and trunk cylinders.